The mantle is on the pallet. The plant is locked out. Then someone asks where the cutting ring is — and the outage stretches by a shift. Most “liner” change-outs stall because one-time retention hardware, lock parts, or the feed plate never made the kit list.
This page is a brand-free fastening / retention checklist for cone rebuild crews and parts buyers: torch-ring style cutting rings, mantle lock nut/bolt families, feed plate/feed cone, wedges/shims, and what is one-time vs inspect-and-reuse. It sits beside the cone mantle / bowl liner RFQ (liner selection) and expands the brief nut / burning-ring notes in how to extend cone wear life. Quote kits by part number / model match. Torque values stay with the machine manual and site procedure — this is not a universal Nm chart.
Answer first: what to replace every mantle change?
Q: What should I replace every cone mantle change?
A: Plan on a new torch/cutting ring, inspect or renew the lock nut/bolt, and usually renew the feed plate/feed cone with the mantle. Bowl-side wedges/shims and bolts are inspect-and-replace. Backing compound cushions — it does not replace proper fastening. Quote by part number / model match for the full kit, not the mantle alone.
Table A — Parts map (functional names)
Describe hardware by function, not by branded series names.
| Item | Role | Typical replace cadence |
|---|---|---|
| Mantle (head liner) | Moving wear surface | Campaign end |
| Concave / bowl liner | Fixed wear surface | Often with mantle; confirm wear |
| Torch ring / cutting ring | Retention / cut-off aid at nut | Usually every mantle change (non-reusable) |
| Mantle lock nut or lock bolt | Preload / retention | Inspect; replace if damaged / stretched |
| Feed plate / feed cone | Protects head / directs feed | Often with mantle |
| Wedges / shims / square bolts (bowl side) | Bowl liner clamp set | Inspect; replace damaged set |
| Backing compound | Cushion / support — not a fastener | Renew per procedure |
| Seat protection / anti-seize rules | Seat integrity | Clean seats; no oil on friction seating faces unless manual says otherwise |
Chamber geometry (coarse / medium / fine pairing) is covered in the chamber profile guide. This checklist assumes you already know which liner pair you are installing.
Table B — One-time vs inspect-and-reuse
| Part | Default practice | Fail signals |
|---|---|---|
| Torch / cutting ring | New each mantle | Distortion, incomplete cut, unknown history |
| Lock nut / bolt | Reuse only if undamaged | Thread galling, ovalization, crack, wrong preload feel |
| Feed plate | Prefer new with mantle | Thinning, cracks, loose fit |
| Bowl wedges / shims | Kit on hand | Rounded heads, missing pins, bent wedges |
| Hex / square bolts | Spot replace | Stretch, corrosion, wrong length mix |
Non-reusable ring rule: if the ring was burned, cut, or distorted in removal — or if history is unknown — treat it as scrap. Reusing a questionable ring to “save one SKU” is a common cause of a mantle that loosens mid-campaign.
Table C — Pre-install inspection gates
Run these gates before the lift, with photos in the job pack.
| Gate | Check | Record |
|---|---|---|
| Identity | PN / model match for ring, nut, mantle, feed plate | Photo of markings |
| Seat | Head/bowl seating faces clean, no fretting ridges | Visual + feeler if used on site |
| Threads | Lock threads clean, gauge if available | Pass/fail |
| Ring fit | Seats square; no rock on old slag | Visual |
| Kit completeness | Ring + lock + feed plate + liner pair + backing | Checklist sign-off |
Dimensional fit features and seating expectations also sit in casting dimensional tolerances. Critical threads on a first article belong in the fitment proof pack when the PN is new or previously troubled.
Safety and tighten method (no invented torque)
- Follow site lockout / tagout and lifting plans.
- Use the machine manual and site procedure for preload and tighten sequence. Do not copy a torque number from a blog post as universal.
- Prefer controlled tighten methods over ad-hoc impact where procedures allow.
- Keep friction seating faces clean and dry unless the manual explicitly calls for a specified compound on that face. Oil on a friction seat is a fretting starter.
- Backing compound supports the liner; it is not a substitute for correct ring and lock hardware.
Table D — Outage kit RFQ (desensitized placeholders)
Use fictional placeholders only. Never paste real customer or catalog competitor part numbers as foundry SKUs. Build the kit line list, then send it through the PN / model-match RFQ template.
| Line | Example placeholder (fictional) | Qty note |
|---|---|---|
| Mantle | PN-MANTLE-EX-001 / model match | 1 |
| Concave | PN-CONC-EX-001 / model match | 1 |
| Torch ring | PN-RING-EX-001 | 1 (consumable) |
| Lock nut or bolt | PN-LOCK-EX-001 | 1 + spare recommended |
| Feed plate | PN-FEED-EX-001 | 1 |
| Bowl clamp odds | Kit by model match | 1 set |
Stock at least one spare consumable ring for the next forced change. Buyers who only ordered “the mantle” are the ones calling mid-outage.
Table E — Common failure modes after bad fastening
| Symptom | Likely cause | Prevention |
|---|---|---|
| Mantle spins / loosens | Wrong preload / reused damaged ring | New ring + correct tighten method |
| Seat fretting | Dirt / oil on friction seat | Clean dry seat per procedure |
| Cracked feed plate early | Missing plate or wrong stack | Always kit feed plate with mantle |
| Uneven liner wear | Loose liner / bad backing | Renew compound; verify clamp |
Uneven wear can also be a chamber or feed issue — cross-check the chamber profile guide before you only blame fasteners.
FAQ
Is every cutting / torch ring single-use?
Default yes for rebuild planning. Rings that were cut, burned, or distorted in removal should not return to service. If a procedure explicitly allows reuse under defined inspection, follow that procedure and document it — do not improvise from habit.
Can I weld instead of replacing a damaged ring or lock part?
Not as a field shortcut in this checklist. Retention hardware is a safety- and fitment-critical stack. Replace damaged rings and lock parts with correct PN / model-match pieces unless a written engineering procedure says otherwise.
Does backing compound replace fastening?
No. Backing cushions and supports. Torch/cutting rings and lock nuts/bolts provide retention preload. Missing either side of that system shows up as loosening, fretting, or uneven wear.
Should I order the lock nut without knowing machine hours?
You can RFQ the nut by part number / model match from the marking or drawing. Hours help plan whether to keep a spare on the shelf; they are not required to identify the correct hardware family.
Are bowl-side and head-side kits the same?
No. Head side typically covers mantle, torch/cutting ring, lock nut/bolt, and feed plate. Bowl side covers concave clamp sets — wedges, shims, bolts. Stock both when the outage opens both sides.
What about lead time?
Lead time depends on stock, pattern status, and MOQ. Ask for a written week range with Incoterms on the quote. This page does not invent day counts.
Why did the mantle loosen after a “successful” install?
Common causes: reused damaged ring, wrong preload method, contaminated friction seat, incomplete clamp on the bowl side, or backing that did not renew with the liner. Photograph seats and hardware condition at install so the next investigation has evidence.
Close
Build the pallet list from Tables A–D before the outage window. New torch/cutting ring every mantle change; inspect lock hardware; kit the feed plate; keep bowl clamp odds on hand. Quote the full fastening kit by part number / model match, not the mantle alone.
See also: cone crusher fastening & spare parts.
GUBT supplies model-match cone liners and related wear hardware as a source foundry. For a kit quote, send Table D lines plus marking photos to info@gubtcasting.com or Contact Us.



